In development

ECU Cat-GDI8

Every cylinder has a direct injector and a port injector. Four cam phasers, fast start and a torque-based control model in one sealed unit for airboat engines.

Cat-GDI8 enclosure with four sealed connectors
Engines2–8 cylinders, V8 in the base version
Injection8 direct (GDI) + 8 port injectors
High-pressure pumps2, one per bank
Ignition8 outputs: 12 V coils or 5 V igniters
Valve timing4 camshafts, 4 cam phasers
H-bridges4: throttles, electric wastegates
ProcessorARM dual-core
CommunicationEthernet · 2 × CAN · LIN
Connectors4 × TE AMPSEAL 35-pin
ControlTorque-based model
Hardware

Enclosure and board

Scroll through the unit — from the sealed enclosure to the board inside.

Cat-GDI8 enclosure with four sealed connectors, 3D model
01 · Hardware

Sealed enclosure

The housing closes the electronics completely: black plastic cover on an aluminium base plate. All wiring enters through sealed connectors.

Cat-GDI8 top view with four sealed connectors, 3D model
02 · Hardware

Four 35-pin connectors

Four sealed TE AMPSEAL 35-pin connectors, one per function group:

  • J1 — sensors and communication
  • J2 / J3 — cylinder banks 5–8 and 1–4
  • J4 — battery power and pumps
Open the pinout
Cat-GDI8 with transparent cover showing the board, 3D model
03 · Hardware

One board inside

A single board carries the dual-core ARM processor and all power stages: drivers for 16 injectors, 8 ignition coils, 2 high-pressure pumps and 4 H-bridges. The connectors are soldered directly to it — no internal harness.

Cat-GDI8 aluminium base plate with cooling fins and rubber mounts, 3D model
04 · Hardware

Cooling and mounting

The aluminium base plate with cooling fins takes heat away from the power electronics. Four rubber mounts isolate the unit from hull and engine vibration.

Cat-GDI8 exploded view: cover, board and base plate, 3D model
05 · Hardware

Simple assembly

Three main parts — cover, board and base plate — are held together with screws, so the unit can be opened for inspection.

Capabilities

What the unit does

One unit controls fuel, air, ignition and valve timing of a V8 engine, and records everything it does.

Hybrid injection

8 direct (GDI) injectors and 8 port injectors. Direct injection with 1–3 pulses per cycle and a high-voltage current profile; the share of port and direct fuel is set in the calibration.

16 injectors · 8 GDI + 8 PFI

High-pressure fuel

Two high-pressure fuel pump valves, one per bank, with closed-loop rail pressure control.

2 HPFP · 2 rails

Variable valve timing

Four camshafts — intake and exhaust on each bank — with four cam phasers. Closed-loop control, oil pressure check, chain and phaser diagnostics, automatic tuning.

4 camshafts · 4 phasers

Fast start

The unit finds the engine position from the camshaft shape before the crank wheel gap arrives, so the first injection and spark come sooner after cranking starts.

Sync in ~190° of crank on average, vs ~310° by the gap

Flexible trigger

Crank wheels 36-1, 60-2, 36-2-2-2 or a cam-only wheel; camshaft shapes are described in the setup tool and checked with the built-in trigger logger.

Up to 4 camshaft inputs

Ignition

Eight outputs for passive 12 V coils with adaptive dwell, or 5 V signals for coils with a built-in igniter.

8 coils · individual timing and knock control

Throttles and wastegates

Four H-bridge outputs for one or two electronic throttles and electric wastegates. End-stop learning and automatic PID tuning; SENT position sensors supported.

4 H-bridges

Torque-based control

Air and torque model, lambda control, two knock sensor channels, wideband lambda and exhaust temperature from a CAN module. Pressures are sampled in sync with crank angle.

2 knock channels · wideband + EGT over CAN

Safety by design

Injection and spark come from hardware timers, never from a data bus. Three levels of supervision with an independent watchdog; on a fault the outputs are switched off. Fault codes in OBD format.

3-level supervision

Setup and logging

Calibration, live data and logs over Ethernet in BrainBus GDI-8. Calibrations are stored with rollback; logs are written to onboard memory. A built-in ECU simulator lets you prepare a calibration before the engine runs.

Ethernet · 2 × CAN · LIN

How it works

The unit has two processor cores. One runs the engine in real time: engine position, fuel, ignition, throttles, high-pressure pumps, cam phasers and knock control. The other handles Ethernet, CAN, diagnostics and logging, and supervises the first one.

The engine setup — trigger wheels, camshafts, injectors, coils, sensors — is done in the BrainBus GDI-8 application, without changing firmware.

Development status

First prototype boards are assembled. Firmware is verified with automated tests and an ECU simulator; testing on a running engine is the next stage. Boost control is planned.

Specifications may change before release. For project inquiries, write to info@ailuohai-tech.com.

Documentation Pinout Firmware
Write to us