Connector pinout, power and ground layout of the Cat-GDI8 engine control unit. Select a connector on the unit, a pin on the connector or a row in the table.
Four TE AMPSEAL 35-pin connectors (776231). Colours show the signal group; select a group to highlight its pins.
Top view of the enclosure, 3D model. Select a connector to open its pinout.
Connector face, pin numbering as in the ECU schematic.
Select a pin on the connector or a row in the table.
| Pin | Signal | Description |
|---|---|---|
| 1 | SENT4 | SENT digital sensor input 4 |
| 2 | SENT3 | SENT digital sensor input 3 |
| 3 | AV2 | Analog voltage input 2 |
| 4 | AV1 | Analog voltage input 1 |
| 5 | GND | Ground |
| 6 | CAN2 H | CAN bus 2, high line |
| 7 | CAN2 L | CAN bus 2, low line |
| 8 | LIN | LIN bus |
| 9 | STARTER | Starter relay high-side output |
| 10 | GND | Ground |
| 11 | KNOCK2+ | Knock sensor 2 input + |
| 12 | KNOCK2- | Knock sensor 2 input - |
| 13 | SENT2 | SENT digital sensor input 2 |
| 14 | SENT1 | SENT digital sensor input 1 |
| 15 | IO6 | Universal analog/digital input 6 |
| 16 | IO8 | Universal analog/digital input 8 |
| 17 | IO10 | Universal analog/digital input 10 |
| 18 | IO12 | Universal analog/digital input 12 |
| 19 | IO13 | Universal analog/digital input 13 |
| 20 | DIN6 | Digital input 6 |
| 21 | DIN5 | Digital input 5 |
| 22 | KNOCK1+ | Knock sensor 1 input + |
| 23 | KNOCK1- | Knock sensor 1 input - |
| 24 | VR- | Crankshaft position sensor (VR) input - |
| 25 | VR+ | Crankshaft position sensor (VR) input + |
| 26 | IO5 | Universal analog/digital input 5 |
| 27 | IO7 | Universal analog/digital input 7 |
| 28 | IO9 | Universal analog/digital input 9 |
| 29 | IO11 | Universal analog/digital input 11 |
| 30 | GND | Ground |
| 31 | DIN4 | Digital input 4 |
| 32 | DIN1 | Digital input 1 |
| 33 | DIN2 | Digital input 2 |
| 34 | DIN3 | Digital input 3 |
| 35 | +5V SENS1 | +5 V sensor supply 1 (output) |
| Pin | Signal | Description |
|---|---|---|
| 1 | IGN5 | Ignition coil 5 driver output (IGBT, low side) |
| 2 | IGN6 | Ignition coil 6 driver output (IGBT, low side) |
| 3 | IGN7 | Ignition coil 7 driver output (IGBT, low side) |
| 4 | IGN8 | Ignition coil 8 driver output (IGBT, low side) |
| 5 | PFI INJ7 | Port injector 7 (PFI), low side |
| 6 | PFI INJ8 | Port injector 8 (PFI), low side |
| 7 | BAT OUT B | Protected +12 V supply output, group B |
| 8 | IGN7 5V | Ignition output 7, 5 V logic signal for coils with built-in igniter |
| 9 | IGN5 5V | Ignition output 5, 5 V logic signal for coils with built-in igniter |
| 10 | ETB3+ | H-bridge 3 output + (electronic throttle or DC actuator) |
| 11 | ETB3- | H-bridge 3 output - (electronic throttle or DC actuator) |
| 12 | ETB4+ | H-bridge 4 output + (electronic throttle or DC actuator) |
| 13 | GND | Ground |
| 14 | GND | Ground |
| 15 | COIL +12V B | +12 V ignition coil supply output, bank B |
| 16 | COIL +12V B | +12 V ignition coil supply output, bank B |
| 17 | PFI INJ5 | Port injector 5 (PFI), low side |
| 18 | PFI INJ6 | Port injector 6 (PFI), low side |
| 19 | IGN8 5V | Ignition output 8, 5 V logic signal for coils with built-in igniter |
| 20 | IGN6 5V | Ignition output 6, 5 V logic signal for coils with built-in igniter |
| 21 | BAT OUT B | Protected +12 V supply output, group B |
| 22 | ETB4- | H-bridge 4 output - (electronic throttle or DC actuator) |
| 23 | LS7 | Low-side output 7 (relay, solenoid, lamp) |
| 24 | INJ8 LS | GDI injector 8 low side |
| 25 | INJ7-8 HS | GDI injector high side, injectors 7 and 8 (pin doubled for current) |
| 26 | INJ7-8 HS | GDI injector high side, injectors 7 and 8 (pin doubled for current) |
| 27 | INJ7 LS | GDI injector 7 low side |
| 28 | INJ6 LS | GDI injector 6 low side |
| 29 | INJ5-6 HS | GDI injector high side, injectors 5 and 6 (pin doubled for current) |
| 30 | INJ5-6 HS | GDI injector high side, injectors 5 and 6 (pin doubled for current) |
| 31 | INJ5 LS | GDI injector 5 low side |
| 32 | HPFP B LS | High-pressure fuel pump valve B, low side |
| 33 | HPFP B HS | High-pressure fuel pump valve B, high side |
| 34 | LS8 | Low-side output 8 (relay, solenoid, lamp) |
| 35 | LS6 | Low-side output 6 (relay, solenoid, lamp) |
| Pin | Signal | Description |
|---|---|---|
| 1 | ETB2- | H-bridge 2 output - (electronic throttle or DC actuator) |
| 2 | ETB1+ | H-bridge 1 output + (electronic throttle or DC actuator) |
| 3 | ETB1- | H-bridge 1 output - (electronic throttle or DC actuator) |
| 4 | IGN2 5V | Ignition output 2, 5 V logic signal for coils with built-in igniter |
| 5 | IGN4 5V | Ignition output 4, 5 V logic signal for coils with built-in igniter |
| 6 | BAT OUT A | Protected +12 V supply output, group A |
| 7 | PFI INJ3 | Port injector 3 (PFI), low side |
| 8 | PFI INJ4 | Port injector 4 (PFI), low side |
| 9 | IGN4 | Ignition coil 4 driver output (IGBT, low side) |
| 10 | IGN3 | Ignition coil 3 driver output (IGBT, low side) |
| 11 | IGN2 | Ignition coil 2 driver output (IGBT, low side) |
| 12 | IGN1 | Ignition coil 1 driver output (IGBT, low side) |
| 13 | LS1 | Low-side output 1 (relay, solenoid, lamp) |
| 14 | ETB2+ | H-bridge 2 output + (electronic throttle or DC actuator) |
| 15 | BAT OUT A | Protected +12 V supply output, group A |
| 16 | IGN1 5V | Ignition output 1, 5 V logic signal for coils with built-in igniter |
| 17 | IGN3 5V | Ignition output 3, 5 V logic signal for coils with built-in igniter |
| 18 | PFI INJ1 | Port injector 1 (PFI), low side |
| 19 | PFI INJ2 | Port injector 2 (PFI), low side |
| 20 | COIL +12V A | +12 V ignition coil supply output, bank A |
| 21 | COIL +12V A | +12 V ignition coil supply output, bank A |
| 22 | GND | Ground |
| 23 | GND | Ground |
| 24 | LS4 | Low-side output 4 (relay, solenoid, lamp) |
| 25 | LS2 | Low-side output 2 (relay, solenoid, lamp) |
| 26 | HPFP A LS | High-pressure fuel pump valve A, low side |
| 27 | HPFP A HS | High-pressure fuel pump valve A, high side |
| 28 | INJ4 LS | GDI injector 4 low side |
| 29 | INJ3-4 HS | GDI injector high side, injectors 3 and 4 (pin doubled for current) |
| 30 | INJ3-4 HS | GDI injector high side, injectors 3 and 4 (pin doubled for current) |
| 31 | INJ3 LS | GDI injector 3 low side |
| 32 | INJ2 LS | GDI injector 2 low side |
| 33 | INJ1-2 HS | GDI injector high side, injectors 1 and 2 (pin doubled for current) |
| 34 | INJ1-2 HS | GDI injector high side, injectors 1 and 2 (pin doubled for current) |
| 35 | INJ1 LS | GDI injector 1 low side |
| Pin | Signal | Description |
|---|---|---|
| 1 | AV4 | Analog voltage input 4 |
| 2 | AV3 | Analog voltage input 3 |
| 3 | IO14 | Universal analog/digital input 14 |
| 4 | CAN2 H | CAN bus 2, high line |
| 5 | CAN2 L | CAN bus 2, low line |
| 6 | CAN1 H | CAN bus 1, high line |
| 7 | CAN1 L | CAN bus 1, low line |
| 8 | NC | Not connected (reserved) |
| 9 | NC | Not connected (reserved) |
| 10 | NC | Not connected (reserved) |
| 11 | NC | Not connected (reserved) |
| 12 | NC | Not connected (reserved) |
| 13 | +5V SENS2 | +5 V sensor supply 2 (output) |
| 14 | GND | Ground |
| 15 | GND | Ground |
| 16 | LIN | LIN bus |
| 17 | IO15 START | Universal input 15, used as start button input |
| 18 | KL15 | Ignition switch input (+12 V when ignition is on) |
| 19 | GND | Ground |
| 20 | GND | Ground |
| 21 | GND | Ground |
| 22 | LS5 | Low-side output 5 (relay, solenoid, lamp) |
| 23 | BAT OUT B | Protected +12 V supply output, group B |
| 24 | LS3 | Low-side output 3 (relay, solenoid, lamp) |
| 25 | BAT OUT A | Protected +12 V supply output, group A |
| 26 | KL30 GDI | Battery +12 V input for the GDI injector stage |
| 27 | KL30 GDI | Battery +12 V input for the GDI injector stage |
| 28 | KL30 COIL | Battery +12 V input for the ignition coil stage |
| 29 | KL30 COIL | Battery +12 V input for the ignition coil stage |
| 30 | FUEL PUMP 1 | Fuel pump high-side output 1 |
| 31 | FUEL PUMP 2 | Fuel pump high-side output 2 |
| 32 | KL30 PUMP | Battery +12 V input for the fuel pump and starter outputs |
| 33 | KL30 PUMP | Battery +12 V input for the fuel pump and starter outputs |
| 34 | KL30 A/B | Battery +12 V input for supply outputs A/B |
| 35 | KL30 A/B | Battery +12 V input for supply outputs A/B |
J2 and J3 carry the two cylinder banks; J1 collects sensors and buses; J4 brings in battery power and drives the pumps.
Battery supply is split into separate KL30 groups; each group uses two pins. Connect all ground pins.
| Signal | Purpose | Pins |
|---|---|---|
| KL30 GDI | Battery +12 V, GDI injector stage | J4: 26, 27 |
| KL30 COIL | Battery +12 V, ignition coil stage | J4: 28, 29 |
| KL30 PUMP | Battery +12 V, fuel pump and starter outputs | J4: 32, 33 |
| KL30 A/B | Battery +12 V, supply outputs A/B | J4: 34, 35 |
| KL15 | Ignition switch input | J4: 18 |
| GND | Ground | J1: 5, 10, 30; J2: 13, 14; J3: 22, 23; J4: 14, 15, 19, 20, 21 |
Setup, live data and logs work over Ethernet in the BrainBus GDI-8 application. It will be published on the Downloads page together with the product release.
Pinout and specifications are preliminary and may change before release. Questions: info@ailuohai-tech.com.